Numerical control punching machine commands

104511) suspends calling the police PLC(82.

104309) is urgent stop to call the police PLC(80.

104793) drift mould holder was not opened call the police PLC(105.

The lower mould when 101559) punching machine retreats a mould gets stuck, former without fall back on call the police PLC(00.

070116) punching machine detects when the mould, which a few labour detect be less than PLC(05.

102606) moves when clip, drift did not install mould PLC(05.

101566) induction does not arrive to already called the police of lower mould PLC(82.

Dead machine of 104303) punching machine calls the police PLC(82.

Circuitry of 104101) emergency stop button smokes oily electric machinery not to have signal PLC(05.

101091) discharge board not safe arrive to pass or have guide content gets stuck and inductor discovers discharge board did not arrive at origin happening to call the police PLC(05.

102191) mould runner coming back does not get stuck, block a mould to rotate gear inductor did not arrive call the police PLC(80.

104332) matchs electric equipment switch to jump make call the police, match electric equipment temperature to cross switch of tall air conditioning to jump make call the police PLC(82.

104112) common gas presses inadequacy to call the police PLC(80.

104301) convulsions motor gets stuck to call the police PLC(05.

101517) breeds mount of the upper mould when the mould, lower mould was not installed reach the designated position call the police PLC(05.

The positional sideslip of 101564) viewfinder, radial induction does not reach the designated position call the police, the ejaculation that produces infrared ray the light goes short circuit to call the police PLC(05.

Without infrared ejaculation the lamp appears when mould of 101565) remove stage makeup and costume short circuit is fiber-optic line inductor calls the police PLC(05.

Inductor of 101577) fiber-optic line calls the police PLC(05.

Head of 101576) mould concussion is sordid, archives so drift does not take radial induction to call the police to the mould fixed position connects a fast G93=_ _177TRANS XY to be the same as direction of 357 355 2048 quickly contrary G67IX of fixed position of 357 commands rectangular G72XY is long.

JY is long.

P mould.

Q mould.

T is fair; G72G68I radius.

J angle rises.

K angle.

P mould.

Q interval.

(Q is not more than spare parts of 8)D board thick G72(to machine) G98IX direction arranges interval.

JY direction arranges interval.

PX direction interval is counted.

KY direction interval is counted.

G04 stops + X(time) formulary G90X.

Y.

Fixed position T is fair a =X.

Y.

T is fair (have strong) G70G9G91X.

Fixed position (without strong) G90Y.

Fixed position (have strong) sealed X.

Y.

Fixed position T is fair a G29I radius.

J angle.

P interval.

(P is not more than 8)K amount (the point is not increased after K) G75G76W__ .

Q__ Q1 is left top right corner of Q4 of top left corner is secret length of G68I of aperture G72 fixed position.

J angle.

P mould.

Q feed is measured.

K feed angle.

T is fair a T of; XY fixed position is fair a G28I radius.

J angle.

K rushs much smaller (the point need not be increased after K) G72 is added before XY locates small T of fixed position of an aperture XY is fair a G26I radius.

J angle.

K rushs much smaller (the point need not be increased after K) G72 is added before XY locates small a Kong Wei knows XY fixed position T is fair a G36I-10.

(Length) J-6.

(Width) P41.

(Length several) K5;(width several, the point is not increased after K) G37I10.

J6.

P41.

G69I310 of fixed position of K4; sealed G72.

(Length) J180.

(Angle) P5(mould) Q5(feed measures) .

T is fair a G79I310.

(Length) J180.

(Angle) P5(mould) Q5(feed measures) .

T is fair a D1.

5(board is thick) it is not OK to notice close aperture I day at or at 8 duplicate commands A1B2 is but formulary G72X.

Y.

Fixed position A1; G66I.

J.

P.

Q.

T; G72X.

Y.

Hydraulic pressure of M510 M551M560 M563M502 M505 of B2 begin end rushs cannot M00 pauses 357 Zun Zheng is right negative press attestation of angle direction instead with village cropland machine Zun Zheng is right negative CNC Milling CNC Machining