In AutoCAD R14, pattern plate file is patulous name with Dwt, default method is in AutocadTemplate. When the new document that when us need scale has same setting one batch, the person that use designs pattern plate by his need, discharged the suffering that repeats a setting for many times so. Will see the particular move that designs pattern plate below: 1. After beginning to start AutoCAD R14, in Start Up dialog box, click Start FromScratch, metric chooses in SelectDefault (metric) , click OK pushbutton open next a blank pursues newly. 2. Setting plot unit and graph are restricted: Choose Format/Units Control dialog box, default the unit is Decimal (decimal) , can undertake installing according to need. Choose the setting that Format/Drawing Limits has pursueing bounds, in command travel default the graph is restricted left next horn are (0, 0) , press carriage return can, occurrence graph is restricted coordinate of top right corner is (420, 297) , the graph of A3 width of cloth that this is a standard is restricted. If want to install other width of cloth, the coordinate of top right corner with corresponding input is worth can. After the graph is restricted to change, clicked Zoom All icon only, the coordinate limit that shows on screen just is restricted to match with the graph of the setting, glyph, dimension is tagged etc, also can undertake installing according to need. 3. Set a layer: Click an icon, open Layer ＆ Linetype Properties (layer and line attribute) dialog box, in default protuberant Layer label issues the setting that has a layer. There is only in list at this moment, namely 0, click New pushbutton, a new layer appears in list instantly. When designing pattern plate, basically be layer name, color, line to the setting of the layer model 3, other maintains default each to install can. When new layer just was built default layer name is Layer1, and be in can compile position, the layer name that keys in you to want at this moment can, be like layer of entitle wide solid line. Install the color of the layer, the pane that should click delegate color only can, open SelectColor (color chooses) dialog box, after choosing a kind of color from which, click OK pushbutton to return dialog box of Layer ＆ Linetype Properties again. Set a line then model, last when click a parameter, open SelectLinetype (choice line) dialog box, there is line of a kind of Continuous Solid only below default condition model, namely solid line. Should choose other route model, need lades first them, click Load pushbutton, open Load OrReload Linetype (lade line or reshipment line) dialog box, the route that chooses a need, optional outfit a variety of lines, click OK pushbutton, return SelectLinetype dialog box, the line that new clothes joins appear inside list casing, assign a kind of route to the layer at this moment model. Click OK pushbutton, return dialog box of Layer ＆ Linetype Properties, ordinal setting other each. Final proposal adds to be used at the layer of draw cartography casing and caption column, this outside the name that remove a layer, other is installed by default can. In the setting of the layer, line list does not have the cent of line degree of finish, so how will set wide solid line and fine solid line? It is so in AutoCAD, the degree of finish of line is distinguishing on screen, when printout is installed, through Plot Configuration (the configuration that print) Pen Assignments (plot pen is installed) , according to the line model color will undertake Pen Width(pen wide) setting, to laser or ink jet printer, pen Width is worth the fill width that is solid line. 4. Draw cartography casing and caption column: Affirm current layer is " picture frame layer " , according to the measure that national level provides, use rectangle makes picture frame and caption column with linear tool draw. To the wide solid line in picture frame and caption column, answer to install its the color that differs with fine solid line, so that be like before be narrated can come according to the color of line when printout set its width. The character in clicking tool column inputs a tool " A " , in caption column need fills in literal position pulls a text casing, right now dialog box of Multiline Text Editor is opened, set the parameter of good writing, input needs character. After finishing, click a layer to control a tool, open dialog box of Layer ＆ Linetype Properties, click " picture frame layer " medium lock form icon, will " picture frame layer " the lock is decided, such, when using scale of this pattern plate to pursue newly later " picture frame layer " entity is in cannot compile position, avoided the change that causes because of be being operated by accident. Instead of will current finally layer " 0 " layer. 5. File of memory pattern plate: Choose File/Save As, dialog box of occurrence Save Drawing As, the setting deposits catalog to be Template, file format is DrawingTemplate File(＊ . Dwt) , namely format of pattern plate file, have a name to pattern plate file, click OK pushbutton to finish finally. CNC Milling
CNC Machining